BNLCD - AUTOMOTIVE BODY FILLER, DX-999

  • MSDS: BNLCD
  • Manufacturer: FIBRE GLASS EVERCOAT CO INC
  • Product Name: AUTOMOTIVE BODY FILLER, DX-999
  • National Stock Number: 8030-00N026688
Product Identification

Product ID:AUTOMOTIVE BODY FILLER, DX-999
MSDS Date:10/09/1990
FSC:8030
NIIN:00N026688
MSDS Number: BNLCD

Responsible Party
FIBRE GLASS-EVERCOAT CO.,INC.
6600 CORNELL ROAD
CINCINNATI, OH 45242-2033
US

Emergency Phone: 800-543-4530

Info Phone: 513-489-7600

Preparer: JEFF ZYCH

Cage: 18731

Contractor
FIBRE GLASS-EVERCOAT CO INC
CINCINNATI, OH 45242 US

Telephone: 513-489-7600

Cage: 18731

Ingredients

5 @ 68F.

CAS: 100-42-5

RTECS: WL3675000

Fraction By Weight: 15.52%

OSHA PEL 100 PPM

ACGIH TLV: S,50PPM/100STEL;9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS


POLYESTER RESIN

Fraction By Weight: 25%


TALC (POWDER), CONTAINING NO ASBESTOS FIBERS

CAS: 14807-96-6

RTECS: MW2710000

Fraction By Weight: 60%

OSHA PEL 2 MG/M3 RDUST

ACGIH TLV: 2 MG/M3 RDUST

Hazards

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:YES OSHA:NO
Health Hazards Acute and Chronic:INHALATION OF REPEATED HIGH
CONCENTRATIONS MAY CAUSE LIVER AND KIDNEY DAMAGE.
Explanation of Carcinogenicity:STYRENE: GROUP 2B (IARC).
Effects of Overexposure:INHAL:VAPS MAY CAUSE NOSE/THROAT & RESP TRACT
IRRIT. HIGH CONC MAY CAUSE HDCH & NAUS. RPTD HIGH CONC EXPOS MAY
CAUSE LIVER & KIDNEY DAM. SKIN CONT:PRLNGD/FREQUENT CONT MAY CAUSE
DEFAT/DRYNESS W/IRRIT & POSS DERM. EYE:MAY CAUSE TEARING & IRRIT.
SKIN ABSORB:DERM & IRRT. INGEST:MAY CAUSE GI DISTURBANCES/PAIN &
DISCOMFORT.
Medical Cond Aggravated by Exposure:LIVER AND KIDNEY DISORDERS.

First Aid

First Aid:SKIN: WASH W/SOAP & WATER. EYES: FLUSH W/WATER FOR AT LEAST
15 MINUTES AND GET MEDICAL ATTENTION. INHAL: REMOVE FROM EXPOSURE.
IF UNCONSCIOUS GIVE ARTIFICIAL RESPIRATION OR OXYGEN AS NEEDED. GET
MEDIC AL ATTENTION. INGEST: DO NOT INDUCE VOMITING (ASPIRATION
HAZARD). GET MEDICAL ATTENTION.

Fire Fighting

Flash Point Method:CC
Flash Point:98.0F,36.7C
Lower Limits:1.1%
Upper Limits:6.1%
Extinguishing Media:FOAM, ALCOHOL FOAM, CO*2, DRY CHEMICAL, WATER FOG.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:POLYMERIZATION MAY TAKE PLACE AT ELEVATED
TEMPERATURE SUCH AS IN A FIRE. IF CONTAINED, VIOLENT RUPTURE MAY
RESULT.

Accidental Release

Spill Release Procedures:REMOVE SOURCES OF IGNITION. ABSORB SPILL WITH
ABSORBENT MATERIAL SUCH AS VERMICULITE OR SAND.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:AVOID STORAGE ABOVE 100F. STORE ONLY
IN ORIGINAL CONTAINERS.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.

Exposure Controls

Respiratory Protection:NIOSH/MSHA APPROVED CANISTER TYPE RESPIRATOR
MUST BE WORN TO PREVENT THE INHALATION OF VAPORS OF SPRAY MISTS
WHEN THE TLV OR PEL IS EXCEEDED. WEAR A NIOSH/MSHA APPROVED DUST
MASK WHEN SANDING THE CURE D PRODUCT.
Ventilation:PROVIDE SUFFICIENT MECHANICAL GENERAL AND/LOCAL EXHAUST
VENTILATION. MAINTAIN EXPOSURE BELOW TLV.
Protective Gloves:CHEMICAL RESISTENT GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:USE A BARRIER CREAM SUCH AS GLOVE COAT WHEN
USING THE PRODUCT.
Work Hygienic Practices:REMOVE AND WASH CONTAMINATED CLOTHING. WASH
HANDS BEFORE EATING AND DO NOT SMOKE WHILE USING.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

Chemical Properties

HCC:F4
Boiling Pt:B.P. Text:295F,146C
Vapor Density:HVR/AIR
Spec Gravity:15 LBS/OAL
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:NIL
Appearance and Odor:PASTE, SHARP AROMATIC ODOR.

Stability

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS AND OXIDIZING AGENTS.
Stability Condition to Avoid:HEAT AND DIRECT SUNLIGHT.
Hazardous Decomposition Products:HEATING TO DECOMPOSITION MAY CAUSE
IRRITATING ACRID FUMES.
Conditions to Avoid Polymerization:IF HAZARDOUS POLYMERIZATION OCCURS
WHILE CONTAINED IN A CLOSED CONTAINER, VIOLENT RUPTURE MAY RESULT.

Disposal

Waste Disposal Methods:SMALL QUANTITIES CAN BE REACTED WITH THE
APPROPRIATE HARDNER TO SOLIDIFY. DISPOSE OF I/A/W FEDERAL, STATE
AND LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.